May 1, 2017 (Vol. 37, No. 9)
Payal Khandelwal Ph.D. Global Product Manager, Protein Purification Business Bio-Rad Laboratories
An IMAC Resin for a Highly Productive Histidine-Tagged Protein Purification Process
Since the introduction of recombinant insulin as a therapeutic protein to treat diabetes in the early 1920s, proteins have increasingly been used for therapy. The use of proteins as therapeutics demands a cost- and purity-efficient purification process.
Proteins are relatively easier to purify when they are tagged with a short sequence that can bind to an immobilized matrix and result in separation. Histidine tags are one of the most commonly used tags. The use of immobilized metal affinity chromatography (IMAC) to purify a histidine-tagged protein was shown by Hochuli in 1988. Since then, many histidine-tagged proteins have been purified by IMAC, and IMAC resins themselves have undergone numerous advancements.
Currently, IMAC is commonly used for the first/capture step in purification processes, followed by ion exchange and/or mixed-mode chromatography for the later purification steps. Bio-Rad has recently designed a scalable IMAC resin to enhance the cost and time efficiency of histidine-tagged protein purification processes.
Use of IMAC at Process Scale
Selection of an IMAC resin with the most efficient features is critical for process protein purification. A resin with a large bead size (>90 µm) might not generate high back pressure at the required flow rates, but runs the risk of having a low dynamic binding capacity (DBC) (Figure 1A), which is not ideal for process purification. A resin with a small bead size (<35 µm) might have a relatively higher DBC (Figure 1A), but can run the risk of generating high back pressures at the flow rates required for process purification.
This can be detrimental, as high back pressures can compromise the integrity of the column. Process-scale purifications require a resin with an optimized bead size that retains a high DBC while allowing high flow rates, without generating excessive back pressure. The Nuvia™ IMAC resin incorporates these features. We performed a flow rate vs. DBC analysis on Nuvia IMAC and four commercially available IMAC resins. Nuvia IMAC provided consistently high DBC (>40 mg/mL), even at flow rates of 300 cm/hr (Figure 1A), which ensures a quick, time-efficient purification, making Nuvia IMAC suitable for process purification.
In comparison, most of the other resins tested showed decreasing DBC with increasing flow rates. Resin 1 showed higher DBC than Nuvia IMAC, most likely due to its small pore size. However, the potential for an increase in back pressure with high flow rates has to be considered during process purification. In order to estimate if the back pressure generated in Nuvia IMAC under high flow rates was within the acceptable range for process purification, we performed a pressure flow curve with a histidine-tagged protein. The column pressure remained below 2 bar at a linear velocity of 300 cm/hr (Figure 1B), indicating that Nuvia IMAC can be used at process-scale levels. In addition, Nuvia IMAC resin showed no significant loss in its DBC over more than 100 cycles of repeated use (Figure 1C), making it a cost-effective option.
Typically, depending on the column size, the column performance can vary, despite similar packing. This warrants an upfront investment of cost and time to optimize the process-scale column packing for the most efficient column performance. Nuvia IMAC shows reproducibility in packing efficiency at small- and large-scale in terms of asymmetry (As) and reduced height equivalent of theoretical plate (rHETP), as shown in Table 1. This enhances the efficiency of the purification.
Histidine-Tagged Purification Process
We used Nuvia IMAC in a purification process devised for therapeutic proteins with the intent of purifying a protein with minimal endotoxin and leached nickel levels. Endotoxin levels were tested using a LAL assay and nickel levels were quantitated by ICP-MS analysis (the data shown below will be published in detail in a forthcoming publication).
Capture purification. A recombinant histidine-tagged protein was loaded onto a column packed with Nuvia IMAC. The protein was eluted in a bind-elute mode with imidazole. The eluted protein was >90% pure.
Intermediate purification. The intermediate purification was performed on
Bio-Rad’s Nuvia cPrime™ mixed-mode resin. This resin combines hydrophobic interaction and cation-exchange chromatography capabilities (HIC and CEX, respectively). The eluate from the capture step was loaded and washed and the protein was collected in flow-through mode. Sample analysis showed decreased host cell protein (HCP) contamination. In addition, decreased levels of endotoxin content and leached nickel from the prior step were also seen (Table 2).
Polish Purification. Polish purification was performed on CHT™ ceramic hydroxyapatite mixed-mode media. This media combines affinity interaction and CEX capabilities. The pretreated eluate from the previous step was loaded onto the CHT column. The protein was extracted in bind-elute mode. Analysis of the eluted samples showed negligible endotoxin and leached nickel (Table 2).
IMAC purification for histidine-tagged proteins offers numerous advantages including low costs, simplicity of use, and robust purification efficiencies. Nuvia IMAC resin offers these features, in addition to simple scalability. This enhances the efficiency of the purification process and makes Nuvia IMAC an ideal resin for process purification. This resin is also compatible with a broad array of chemicals and exhibits stability in the presence of commonly used protein purification reagents.