GEN Exclusives

More »

Tech Notes

More »
Aug 1, 2009 (Vol. 29, No. 14)

Single-Use Noninvasive Sensing Technology

Novel Tools Focus on Critical Process Parameter Monitoring in Disposable Systems

  • Pressure Sensors

    Click Image To Enlarge +
    Figure 1. Depth and sterile filtration processes with single-use sensors

    Pressure is one of the most ubiquitous process parameters. Many bioprocess unit operations are either controlled based on pressure or have significant pressure-related safety issues. When pressure monitoring is applied to single-use applications, however, it is routinely relegated to ancillary status.

    Two classic examples are the bioreactor and the primary recovery process steps. Traditional stainless steel reactors are monitored and controlled for pressure, as pressure is used as a means of influencing mass transfer and mitigating contamination. In addition, a high-pressure event is a potentially hazardous situation.

    Single-use bioreactor systems, on the other hand, are frequently not monitored or controlled for pressure because stainless steel pressure transducers are not compatible or cost effective when applied to disposable bioreactors. As a result, a clogged vent filter on a bioreactor can easily rupture bags, spilling the contents of the reactor and exposing the operators to unprocessed bulk.

    Another application where pressure monitoring is central to process performance is depth and sterile filtration. A filter’s capacity is primarily measured by either flow decay or pressure increases, although adding reusable traditional pressure transducers to a process train defeats the purpose of a single-use process set-up. Depending on the process application, the product contact surface of a traditional device requires either sanitization or moist heat sterilization.

    There are traditional devices that are compatible with steam in place, where only the product contact surface is exposed to steam, and even devices that can be placed in an autoclave where the entire device is exposed to steam. Many single-use process components, however, are not compatible with moist heat sterilization temperatures so there may be a requirement for separate sterilization of the stainless steel device and possibly nonoptimal connection to a pre-sterilized disposable assembly.

    The application of piezo electric micro-electro-mechanical system (MEMs) pressure sensors with standard or braided silicone tubing mitigates the need for any batch-to-batch cleaning or any product changeover to be done.

    Single-use pressure sensing allows for rapid changeover of product contact parts in both development applications and especially in early-phase clinical manufacture. Single-use pressure sensors from PendoTECH were designed to enable pressure measurement with single-use assemblies that have flexible tubing as the fluid path (Figure 1). 

    These single-use pressure sensors are gamma compatible (up to 50 KGy), and the fluid-path materials meet USP Class VI guidelines and are also compliant with EMEA 410 Rev 2 guidelines. The sensors are manufactured in a Class 100,000 cleanroom to minimize introduction of foreign matter, and each sensor is tested for leaks, accuracy, and electrical specification. In addition, the sensors are compatible with typical bioprocessing solvents.

  • Click Image To Enlarge +
    Figure 2. PendoTECH single-use pressure sensors

    On a single-use bioreactor, a sensor can be installed on a vent line to measure headspace pressure (Figure 2).  Even though the sensors are qualified for use up to 75 psi, the core sensor is accurate in the low-pressure range required for a single-use bioreactor (Figure 3).

    When implementing single-use technology into a process train, the measurement of key analytics is critical and should not be sacrificed or overlooked. It is incumbent upon the manufacturer, user, and quality and safety organizations to make sure the appropriate sensing technology is suitably integrated.

  • Click Image To Enlarge +
    Figure 3. Data from six sensors at low pressures

Add a comment

  • You must be signed in to perform this action.
    Click here to Login or Register for free.
    You will be taken back to your selected item after Login/Registration.

Related content


GEN Jobs powered by connects you directly to employers in pharma, biotech, and the life sciences. View 40 to 50 fresh job postings daily or search for employment opportunities including those in R&D, clinical research, QA/QC, biomanufacturing, and regulatory affairs.
More »

Be sure to take the GEN Poll

Patient Access to Genetic Information

Do you think patients have the absolute right to gain access to their own genetic information from medical or clinical laboratories?

More »