GEN Exclusives

More »

Tutorials

More »
Nov 15, 2010 (Vol. 30, No. 20)

Screening Proteins for Manufacturability

Technology Permits Characterization and Preformulation Studies

  • The complex 3-D structure of a protein ultimately determines its biological function. As such, maintaining the native conformation is clearly of critical importance if the protein in question is to be used as a therapeutic. Additionally, loss of higher order structure through complete unfolding or generation of partially folded intermediates can lead to rapid, irreversible aggregation, which can lead to problems ranging from loss of material during production to a raised immune response in patients.

    The higher order structure of many proteins is susceptible to partial or total unfolding caused by a range of stresses including temperature, pH, or shear forces. The biopharmaceutical developer, therefore, needs to devise strategies to limit or prevent unfolding and aggregation when proteins are inevitably exposed to stresses during manufacture, storage, and use.

    Although protein stability and aggregation resistance can be enhanced through the use of a range of additives at the formulation stage, there is a compelling argument to select or design a fundamentally stable and aggregation-resistant protein as early as possible during the development process. Trying to progress a fundamentally unstable protein can be fraught with difficulty, risk, and cost.

    Unfortunately, however, it is often the case in early-stage development that there are many candidate molecules with acceptable affinity for their targets but that the candidate protein, time, manpower, and other resources are all in short supply. This can severely restrict the extent of experimental work that can be performed and consequently limit the amount of information upon which to base informed decisions about which candidate to take forward.

  • Physical-Stability Screening

    Click Image To Enlarge +
    Figure 1. (A) Effect of unfolding on protein intrinsic fluorescence spectra, note the change in intensity and the shift of the emission to longer wavelength. (B) Plot of intrinsic protein fluorescence spectrum peak shift with temperature showing transition from folded to unfolded conformation and transition mid-point, Tm. (C) Plot of static light scattering intensity as a function of temperature showing onset of thermally induced aggregation and aggregation onset point, Tagg.

    In order to provide biopharmaceutical developers with more information at an earlier stage low sample volume or scale-down analytical technologies are required. The Optim 1000 developed by Avacta Analytical has been designed to provide information about conformational stability and aggregation propensity with high throughput and using small amounts of protein, with the added benefit of fully automated operation, data analysis, and reporting.

    The development of a specialized sample holder or microcuvette array (MCA) allows the system to analyze up to 48 samples in one run using as little as 1 µL of protein solution in each sample. Depending on the sample and application this can mean using concentrations to below 0.1 mg/mL, corresponding to 100 ng of protein per sample.

    The MCA permits high-quality fluorescence and light-scattering data to be recorded from these small volumes, and thermoelectric heating and cooling allows the samples to be subjected to a thermal ramp or held at a fixed temperature during analysis.

    In the basic instrument the samples are analyzed by two techniques simultaneously: intrinsic protein fluorescence spectroscopy is used to monitor protein tertiary structure and static light scattering is utilized to monitor protein aggregation. In addition, extrinsic fluorescent dyes can be added to the sample to give complementary information about protein conformation and aggregation. These analytical techniques are particularly well suited to rapid, sensitive analysis of small volumes of protein in the widest range of possible buffer or solvent conditions.

    In a typical experiment to elucidate stability and aggregation propensity, the protein samples are heated while their intrinsic fluorescence and light-scattering signals are simultaneously monitored. Figure 1 shows typical output of such an experiment.

    Changes in the fluorescence emission (Figure 1A) show the loss of higher order structure and that the protein is thermally denatured. By monitoring this signal, Optim can determine a temperature midpoint, Tm, of the unfolding transition (Figure 1B). The scattered light intensity increases strongly when aggregates are formed and this can be characterized using a second parameter, the aggregation onset temperature, Tagg (Figure 1C).

    These parameters can be used to screen different candidate proteins or explore the effect of different buffer conditions and additives on protein structure and aggregation. The data generated is comparable to that produced by alternative technologies such as differential scanning calorimetry, circular dichroism, and dynamic light scattering, but Optim is typically much faster and uses orders of magnitude less protein.



Related content

Jobs

GEN Jobs powered by HireLifeScience.com connects you directly to employers in pharma, biotech, and the life sciences. View 40 to 50 fresh job postings daily or search for employment opportunities including those in R&D, clinical research, QA/QC, biomanufacturing, and regulatory affairs.
 Searching...
More »

GEN Poll

More » Poll Results »

Ebola Vaccines

When do you think an Ebola vaccine will be available for the general public?